Rupert Neve Designs 5051 Shelford Inductor EQ and Compressor (vertical only)

The Rupert Neve Designs Shelford 5051 combines a three-band Inductor EQ based on Rupert?s vintage designs with the power and flexibility of the Portico II Compressor. Utilizing a fully-discrete Class A signal path and custom audio transformers and inductors, the 5051 delivers all the performance and musicality expected from a Rupert Neve design.

Inductors are wires wound around a coil that provide a form of frequency-dependent resistance. When they saturate, they bring out beautifully musical harmonics that give your tracks the smooth, polished sound that has made Rupert?s consoles and equipment so desirable for over fifty years. This is what makes them different from capacitor-based EQ designs, which do a great job at surgical equalization. But inductors provide the tone.

While it is certainly possible to create a functioning EQ using off-the-shelf inductors, RND choose to use their own custom inductors for the 5051. This attention to detail in controlling variables such as the winding and core materials in relation to the surrounding circuitry allows the 5051 to capture the vitality and personality of Rupert?s classic designs.

The 5051?s 3-band, custom-tapped inductor EQ was inspired by RND's favorite elements of Rupert?s vintage EQ designs. The low-frequency band is designed to produce a creamy, resonant bass response similar to a vintage 1064 ? but unlike the vintage modules, the LF band on the 5051 can be used as either a shelf or a peak filter, adding punch, dimension, and control to your low end.

The midrange band is based on that of the 1073, ideal for sweetening vocals and instruments while bringing them forward in a mix, and its proportional ?Q? response makes it well-suited for minimizing problematic frequencies. The high-frequency band is a hybrid vintage/modern design, blending inductor circuitry with capacitor-based topologies to achieve vintage tones with enhanced control. The High Pass filter is an 18dB/octave design with a switchable 60 Hz or 120 Hz corner frequency, and can be used in tandem with the low-frequency EQ to add low-end presence without clouding the source material.

As with Rupert?s most prized classic designs, each EQ section uses low-feedback, Class A discrete electronics to prevent low-level artifacts and harshness from detracting from the tonal shaping. However, this new circuit is a decidedly modern design with updated techniques and components that were simply not available 50 years ago, and is definitely not a clone.

Every compressor has a gain control element in its circuit, and this is generally what determines the ?sound? of the compressor. Some compressors use tubes, some use FETs, some use light-dependent resistors, some use a diode bridge ? but in the 5051, a VCA (Voltage Controlled Amplifier/Attenuator) is used to control the signal?s gain.

In contrast to a diode bridge design like the 5254, which adds a thick, colorful tonality to the source, the 5051 makes use of a very accurate, low noise, low distortion VCA with essentially no sonic signature of its own. This provides an immense amount of dynamic control without leaving a heavy sonic imprint on your tracks or mixes ? perfect for control across an entire console?s worth of channels.

FEED-FORWARD VS. FEED-BACK

This switch changes the point in the signal path where the VCA control voltage is picked off: either before the VCA (feed-forward) or after the VCA (feed-back). In most of Mr. Neve?s earliest designs, feed-back detection was intrinsic to the musical dynamic response. However, the very nature of a feedback compressor limits the attack time of the compression circuit, as the control voltage has already passed through the VCA itself. To offer faster, more technically accurate response times, feed-forward detection was also implemented in the 5051: with the FF / FB switch, both classic and modern VCA responses are available.

RMS VS. PEAK

One of the more unique features of our VCA compressors is the Peak / RMS mode. This switch allows the VCA to respond to both RMS (Root Mean Square) and peak levels. RMS circuits are considered to better mimic the way the ears perceive apparent loudness, while peak circuits tend to directly respond to the waveform voltage, which may be more of a concern for prevention of clipping and maximizing levels. In this case, peak mode uses a combination of both methods to get the best of both worlds, and avoids the drawbacks of each method on its own.

The 5051 receives ?24V rails from an external DC power supply using a 4-pin connection. There are currently two options available: a 25-way 2U rack-mount supply, or a smaller 5-way ?brick? supply.

The 5051 can be mounted in the vertical 2?way wooden racks, 9-way metal racks, or within a 5088?s penthouse section.

• HIGH-FREQUENCY SHELF/PEAK: Selectable at 8 and 16 kHz with continuous gain from -15 to +15 dB, Selectable Peak or Shelf curves
• LINE SELECT: Selects been Line 1 and Line 2 inputs
• MID-PARAMETRIC: Selectable at 200 Hz, 350 Hz, 700 Hz, 1.5 kHz, 3 kHz, and 6 kHz with continuous gain from -15 to +15 dB, selectable Hi Q
• EQ PRE/POST: When engaged, moves the EQ after the compressor
• HPF: Cycles between bypassed, HPF at 60 Hz, and HPF at 120 Hz
• LOW-FREQUENCY EQ: Selectable at 30, 60, 100, and 220 Hz, continuous gain from -15 to +15 dB, selectable Peak or Shelf curves
• LEVEL & GAIN REDUCTION METERS: 8-segment LED meters for monitoring Gain Reduction and Output Level
• MAKE-UP GAIN: Applies post-compressor make-up gain
• RELEASE TIME: Changes the time taken for the gain to return to 0 after the compressor disengages
• SC HPF: Applies a high-pass filter at 250 Hz to the VCA side chain signal
• LINK: Links the 5051 VCA to a 2nd 5051 module, if connected
• ATTACK TIME: Changes the time delay before compression begins
• RATIO: Changes the amount of gain reduction above the set threshold level
• FF/FB: When engaged, changes the VCA detection from feed-forward to feed-back
• COMP IN: Engages the Compressor
• THRESHOLD: Sets the level at which compression begins

Please note: Power supply is not included.